Главная/Диагностика стиральной машины Miele
Диагностика неисправностей стиральной машины Miele
Для поиска неисправности при ремонте стиральной машины Miele воспользуемся сервисным тестом.
Cервисный тест стиральной машины Miele
Для моделей Miele W132, Miele W134, Miele W135,
Miele W914, Miele W916, Miele W917, Miele W918, Miele W921, Miele W930, Miele W957, Miele W110, Miele W115, Miele W120,
Miele W800, Miele W810, Miele W820, Miele W822, Miele W830, Miele W832,
Miele W902, Miele W905, Miele W911, Miele W912, Miele W913, Miele W915
| СВЕТОДИОДНЫЕ ИНДИКАТОРЫ ОШИБОК |
ПРИЧИНЫ НЕИСПРАВНОСТЕЙ |
| On |
- Функция безопасности для детей была активирована и выбранная программа изменится после 3 минут
|
| Pre-Wash (Предварительная стирка) |
- Обрыв линии GND-питания в реле уровня и платы управления.
- Включается только дренажный насос
- Ни один из компонентов не стартует
|
| Main Wash (Основная стирка) |
- датчик температуры NTC или неисправность проводки/короткое замыкание
- Неисправен ТЭН
|
| Rinse 1 & Rinse 2 (
Полоскание 1 & Полоскание 2) |
- Таходатчик неисправен (Неисправность проводки/короткое замыкание)
- Неисправность проводки
- Двигатель не работает, могут быть изношены щетки
|
| Rinse 3 (Полоскание 3) |
- Неисправность модуля управления
(Относится только к EDPW102; EDPW122; EDPW150)
|
| Rinse Hold (Белье остается в воде последнего полоскания. Функция предотвращает цикл стирки от завершения, пока не нажмете кнопку. Это помогает предотвратить образование складок на белье) |
- Неправильно выбрана прграмма - Клиент выбрал 'Несминаемость' через скорость отжима Selector, а затем обращается к сегменту программы отжима. Это противоречит выбору 'Несминаемость'
|
| Final Spin (Заключительный отжим) |
- Заключительный отжим контролируется. В последние 2 секунды заключительного отжима обороты должны быть больше, чем 400 оборотов в минуту.
- Если этого не происходит светодиод будет мигать, пока программа не будет отменена.
- Если селектор скорости отжима был установлен в 400 оборотов в минуту, скорость 450 оборотов в минуту будет достигнута для предотвращения этой ошибки.
|
| Water Drain Check (Проверка слива воды) |
- Drain Fault (Неисправен слив воды)
|
| Water Inlet Check (Патрубок подвода воды) |
- Не был достигнут уровень воды достаточный для начала стирки
- Время для достижения нужного уровня воды было превышено из-за низкого давления воды в системе водопровода
|
| Water Inlet & Water Drain Check (Проверьте слив и залив воды) |
- Система защиты от протекания воды была включена (Относится только к EDPW102; EDPW150)
|
- Выключить все кнопки
- Переключить кнопку в положение "Off"
- Поворот селектор программ в положение "Finish / Start"
- Переключить кнопку в положение "On"
- Нажмите и отпустите кнопку "Pre-wash/Предварительная стирка" три раза в течение 4 секунд. Кнопка "Pre-wash/Предварительная стирка" должна начать мигать.
- Включите переключатель программ на нужную настройку в соответствии со следующей таблицей
| Переключатель |
Function Tested |
| Cottons 95°C |
1 |
Клапан 1 открыт до тех пор, пока уровень стирки 1 не будет достигнут. После этого стартует нагревание до 35 ° С |
| Cottons 75°C |
2 |
Клапан 2 открыт до тех пор, пока уровень стирки 3 не будет достигнут |
| Cottons 60°C |
3 |
Клапаны 2 и 3 открыты до тех пор, пока уровень стирки 3 не будет достигнут |
| Cottons 50°C |
4 |
Клапан горячей воды открыт до тех пор, пока уровень стирки 3 не будет достигнут |
| Cottons 40°C |
5 |
Сливной насос |
| Cottons 30°C |
6 |
Барабан вращается 40 оборотов в минуту в обратную сторону |
| Minimum Iron 60°C |
7 |
Сливной насос работает и барабан вращается в соответствии с выбором скорости отжима |
Cервисный тест стиральной машины Miele на английском языке
| LED Flashes |
Cause of Fault |
| On |
- Child safety feature has been activated and the selected program is altered after 3 mins
|
| Pre-Wash |
- Open circuit in link GND-supply via level switch and control PCB.
- Only the drain pump is activated
- No other component will start
|
| Main Wash |
- NTC Sensor or wiring open/short circuit
- Heater fault
|
| Rinse 1 & Rinse 2 |
- Tacho fault (open/short circuit)
- Wiring fault
- No motor action e.g. worn brushes
|
| Rinse 3 |
- Control PCB fault
(Only relevant to EDPW102; EDPW122; EDPW150)
|
| Rinse Hold |
- Operator fault - The customer has selected 'Rinse Hold' via the Spin Speed Selector, and then accesses the Spin programme segment. This contradicts the 'Rinse Hold' selection
|
| Final Spin |
- The final spin is monitored. The final 2 secs of the final spin must be greater than 400 rpm
- If this does not occur the 'Final Spin' LED will flash until the programme is cancelled.
- If the spin speed selector is set to 400 rpm, then a speed of 450 rpm will be reached to prevent this fault from occurring
|
| Water Drain Check |
|
| Water Inlet Check |
- Wash level has not been reached
- Fill time has been exceeded due to low water pressure
|
| Water Inlet & Water Drain Check |
- Waterproof System float switch has been activated (Only relevant to EDPW102; EDPW150)
|
- Switch off all option buttons
- Switch appliance ‘Off’
- Rotate program selector to the ‘Finish/Start’ position
- Switch appliance ‘On’
- Press and release the ‘Pre-wash’ button three times within 4 secs of switching appliance on ‘Pre-wash’ LED will flash
- Turn program selector switch to the desired setting in accordance with the following table
| Selector Switch |
Function Tested |
| Cottons 95°C |
1 |
Valve 1 opens until wash level 1 is reached. Heating to 35°C then starts |
| Cottons 75°C |
2 |
Valve 2 opens until wash level 3 is reached |
| Cottons 60°C |
3 |
Valves 2 & 3 opens until wash level 3 is reached |
| Cottons 50°C |
4 |
Hot Water valve open until wash level 3 is reached |
| Cottons 40°C |
5 |
Drain Pump |
| Cottons 30°C |
6 |
Drum rotation 40 rpm with reverse action |
| Minimum Iron 60°C |
7 |
Drain pump and spinning in accordance with the spin speed selector |
Коды ошибок неисправностей стиральной машины Miele
Cервисный тест для стиральных машин Miele W933 и Miele W936
Test Mode
- Switch off all option buttons
- Switch appliance ‘Off’
- Close appliance door
- Press & Hold the ‘Soak’ & ‘With Pre-wash’ buttons
- Switch appliance ‘On’
- ‘Pre-wash’ LED will flash & ‘Soak’ LED will illuminate constantly
- The LCD display shows the current version of Electronic PCB fitted
- Press the ‘+’ or ‘-‘ buttons under the LCD display to move through the following options
| Display |
Function Tested |
|
-XX |
ROM version no. indication. |
|
1 |
Valve 1 opens until wash level 1 is reached. Heating to 35°C then starts |
|
2 |
Valves 2 opens until wash level 2 is reached |
|
3 |
Valves 2 & 3 opens until wash level 3 is reachedBleach valve opens - where fitted |
|
4 |
Bleach valve opens - where fitted |
|
5 |
Drain Pump |
|
6 |
Drum rotation 40 rpm with reverse action |
|
7 |
Drain pump and spinning in accordance with the spin speed |
|
8 |
Valve 4 opens until level 3 is reached |
|
9-16 |
N/A |
|
17 |
If the appliance is switched off at this setting, the next time a wash is carried out the LCD will display the wash step no .being carried out and not the time left. The steps can be skipped by pressing the ‘Skip’ touchpad |
|
18 |
After 3 secs the temperature measured by the NTC sensor is shown to the nearest 5°C |
|
19 |
Audible indicator operates |
|
20 |
LED and LCD Display test. Each LED is operated in succession for 0.2 secs followed by each segment of the LCD display |
|
21 |
N/A |
|
22 |
Total operating hours |
|
23 |
The LCD display shows the last 5 faults that have occurred, in coded form. By switching the appliance ‘Off‘ at this point will clear all the fault codes. If no fault is stored ‘cor’ is displayed |
Fault Codes
Access step 23 of the service mode as shown above
| Fault Code |
Cause of Fault |
|
F1 |
Pressure switch fault |
|
F2 |
NTC Sensor fault |
|
F3 |
Heating fault |
|
F4 |
Tacho fault (open/short circuit) |
|
F5 |
Mains Frequency fault |
|
F6 |
Water intake fault |
|
F7 |
Drain fault |
|
Cor |
No fault registered |
Cервисный тест для стиральных машин Miele W934 и Miele W937
Test Mode
- Switch off all option buttons
- Switch appliance ‘Off’
- Close appliance door
- Press & Hold the ‘Soak’ & ‘With Pre-wash’ buttons
- Switch appliance ‘On’
- ‘Pre-wash’ LED will flash & ‘Soak’ LED will illuminate constantly
- The LCD display shows the current version of Electronic PCB fitted
- Press the ‘+’ or ‘-‘ buttons under the LCD display to move through the following options
| Display |
Function Tested |
|
-XX |
ROM version no. indication. |
|
1 |
Valve 1 opens until wash level 1 is reached. Heating to 35°C then starts |
|
2 |
Valves 2 opens until wash level 2 is reached |
|
3 |
Valves 2 & 3 opens until wash level 3 is reachedBleach valve opens - where fitted |
|
4 |
Bleach valve opens - where fitted |
|
5 |
Drain Pump |
|
6 |
Drum rotation 40 rpm with reverse action |
|
7 |
Drain pump and spinning in accordance with the spin speed selector |
|
8 |
Valve 4 opens until level 3 is reached |
|
9-16 |
N/A |
|
17 |
If the appliance is switched off at this setting, the next time a wash is carried out the LCD will display the wash step no .being carried out and not the time left. The steps can be skipped by pressing the ‘Skip’ touchpad |
|
18 |
After 3 secs the temperature measured by the NTC sensor is shown to the nearest 5°C |
|
19 |
Audible indicator operates |
|
20 |
LED and LCD Display test. Each LED is operated in succession for 0.2 secs followed by each segment of the LCD display |
|
21 |
N/A |
|
22 |
Total operating hours |
|
23 |
The LCD display shows the last 5 faults that have occurred, in coded form. By switching the appliance ‘Off‘ at this point will clear all the fault codes. If no fault is stored ‘cor’ is displayed |
Fault Codes
Access step 23 of the service mode as shown above
Some faults cause the current programme to be interrupted in such cases the LCD display to show “---“
| Fault Code |
Cause of Fault |
|
F1 |
Pressure switch fault |
|
F2 |
NTC Sensor fault |
|
F3 |
Heating fault |
|
F4 |
Tacho fault (open/short circuit) |
|
F5 |
Mains Frequency fault |
|
F6 |
Water intake fault |
|
F7 |
Drain fault |
|
Cor |
No fault registered |
Cервисный тест для стиральных машин Miele W935 WPS, Miele W939 WPS, Miele W941 WPS
Test Mode
- Switch off all option buttons
- Switch appliance ‘Off’
- Close appliance door
- Press & Hold the ‘Soak’ & ‘Pre-wash’ buttons
- Switch appliance ‘On’
- ‘Pre-wash’ LED will flash & ‘Soak’ LED will illuminate constantly
- The LCD display shows the current version of Electronic PCB fitted
- Press the ‘+’ or ‘-‘ buttons under the LCD display to move through the following options.
| Display |
Function Tested |
|
-XX |
ROM version no. indication. |
|
1 |
Valve 1 opens until wash level 1 is reached. Heating to 35°C then starts |
|
2 |
Valves 2 opens until wash level 2 is reached |
|
3 |
Valves 2 & 3 opens until wash level 3 is reachedBleach valve opens - where fitted |
|
5 |
Drain Pump |
|
6 |
Drum rotation 40 rpm with reverse action |
|
7 |
Drain pump and spinning in accordance with the spin speed |
|
16 |
The LCD display shows the last 5 faults that have occurred, in coded form. By switching the appliance ‘Off‘ at this point will clear all the fault codes. If no fault is stored ‘cor’ is displayed |
|
19 |
Audible indicator operates |
|
20 |
LED and LCD Display test. Each LED is operated in succession for 0.2 secs followed by each segment of the LCD display |
|
21 |
Total operating hours |
Fault Codes
Some faults cause the current programme to be interrupted in such cases the LCD display to show “---“
| Fault Code |
Cause of Fault |
|
F1 |
Pressure switch fault |
|
F2 |
NTC Sensor fault |
|
F3 |
Heating fault |
|
F4 |
Tacho fault (open/short circuit) |
|
F5 |
Mains Frequency fault |
|
F6 |
Water intake fault |
|
F7 |
Drain fault |
|
Cor |
No fault registered |
Коды ошибок неисправностей стиральной машины Miele